Boot log of the first unit. This is my main one and was sent back to Rob for repair shortly after I got it due to intermittent Disk Not Found errors.
I'll also upload some pics of both units and link to them in a few minutes. This unit is 1st empeg.
empeg-car bootstrap v1.02 20001106 (hugo@empeg.com)
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!
e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.17-rmk5-np17-empeg52-hijack-v394 (mark@rtr.ca) (gcc version 2.
95.3 20010315 (release)) #2 Fri Jun 4 16:34:01 EDT 2004
Processor: Intel StrongARM-1100 revision 11
Checking for extra DRAM:
c1000000: wrote ffffffff, read e91ba9f0
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 30102325) 16MB DRAM
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15016k/16M available (980k code, 20k reserved, 364k da
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options ena
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 636f6972 'rioc'
Found custom animation at offset 0x9a38c
Tuner: loopback=0, ID=-1
Scheduling custom logo.
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
Could not find CS4231A (version=80)
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0005300).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: ÉC²5Ô0´8ÁTÄA°50 , ATA DISK drive
hdb: ÉC²5Ô0´8ÁTÄA°50 , ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: ÉC²5Ô0´8ÁTÄA°50 , 24191MB w/18190kB Cache, CHS=49151
/16/63
hdb: ÉC²5Ô0´8ÁTÄA°50 , 24191MB w/18190kB Cache, CHS=49151
/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman (erik@vt.edu)
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:26:09:1
5
Partition check:
hda: [PTBL] [3083/255/63] hda1 < > hda2 hda3 hda4
hdb: [PTBL] [3083/255/63] hdb1 < > hdb2 hdb3 hdb4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
Timezone: /usr/share/zoneinfo
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...attempt to access beyond end of device
03:05: rw=0, want=2, limit=0
dev 03:05 blksize=1024 blocknr=1 sector=2 size=1024 count=1
EXT2-fs: unable to read superblock
Kernel panic: VFS: Unable to mount root fs on 03:05
Previous Topic
Index
